Browsing by Author "Zhang, Deliang"
Now showing items 1-5 of 49
-
Comparison of blended elemental (BE) and mechanical alloyed (MA) powder compact forging into Ti-6Al-4V rocker arms
(Trans Tech Publications, 2012)Ti-6Al-4V rocker arms for internal combustion engines were produced by forging of compacts of blended powder consisting of elemental hydride-dehydride (HDH) titanium powder and Al60V40 (wt%) master alloy powder or mechanical ... -
Consolidation of ultrafine-grained Cu powder and nanostructured Cu–(2.5–10) vol%Al₂O₃composite powders by powder compact forging.
(Springer, 2010)An as-received ultrafine-grained Cu powder and four nanostructured Cu–(2.5–10) vol%Al2O3 composite powders produced by high-energy mechanical milling of mixtures of the Cu powder and an Al₂O₃ nanopowder were consolidated ... -
Development and design of binder systems for titanium metal injection molding: An overview
(ASM International, 2013)Titanium metal injection molding (Ti-MIM) has been practiced since the late 1980s. Logically, the Ti-MIM practice follows the similar processes developed for the antecedent materials such as stainless steel and ceramics. ... -
The development of porous titanium products using slip casting
(Elsevier, 2013)An optimized titanium slurry was developed from 43 vol.% of titanium powder, 0.3 dw.% of dispersant, 0.8 dw.% of plasticizer and 0.8 dw.% of binder, mixed with a balance of distilled water, which produced a viscosity of ... -
Effect of hot isostatic pressing on mechanical properties of Fe₄₁Cr₁₅Mo₁₄C₁₅B₆Y₂Co₇ BMG
(World Scientific, 2006)Fe-based bulk amorphous rods of 3 mm in diameter and a composition of Fe₄₁Cr₁₅Mo₁₄C₁₅B₆Y₂Co₇ were produced by copper mold casting. The as-cast amorphous rods contain a small (2%) fraction of pores. To close the pores, ...
Co-authors for Deliang Zhang
Supervised by Deliang Zhang
Showing up to 5 theses - most recently added to Research Commons first.
-
Effects of high energy mechanical milling on the kinetics of solid state reactions
(The University of Waikato, 2000)The effects of high energy mechanical milling on the kinetics of solid state reactions in two binary metallic systems, Al-Ni and Cu-Al, and two metal-oxide systems, Al-TiO₂ and Cu(Al)-CuO, have been investigated by using ... -
Modeling and simulation of the dynamic process in high energy ball milling of metal powders
(The University of Waikato, 2000)Mechanical alloying/mechanical grounding by using high-energy ball milling has been considered as a promising materials processing technique to synthesize materials. In this study, modeling simulation has been carried out ... -
Studies of modified pumice and titanomagnetite filtration media
(The University of Waikato, 2001)There is a continuing interest in filtration technologies capable of more efficient filtration, particularly of small microbial particles, but which place less reliance on the use of water treatment chemicals. In order to ... -
Processing, microstructure and mechanical properties of TiₓAlᵧ/Al₂O₃ and Al₂Ti₄C₂/TiₓAlᵧ/Al₂O₃/TiC composites
(The University of Waikato, 2002)The TiₓAlᵧ/Al₂O₃ metal-ceramic composites materials [TiₓAlᵧ is α-Ti(Al,O), Ti₃Al, or TiAl] and Al₂Ti₄C₂/TiₓAlᵧ/Al₂O₃/TiC ceramic-ceramic composites with different volume fractions of ceramic reinforcement phases were ... -
Fabrication and characterization of micro-tubular solid oxide fuel cells
(The University of Waikato, 2004)Solid oxide fuel cells (SOFC) are an energy efficient, low pollution technology for generating power and have the potential to revolutionize energy generation. Tubular and planar concepts are the most common SOFC systems. ...
