Loading...
Thumbnail Image
Publication

Thermal Stability, Microstructures and Mechanical Properties of Nanostructured/Ultrafine Structured Cu-5vol.%Al₂O₃ Nanocomposites Fabricated by High Energy Mechanical Milling and Powder Compact Extrusion

Abstract
Ultrafine structured metal matrix nanocomposites (MMNCs) have received much attention due to their attractive engineering applications and scientific interest. On the engineering aspect, ultrafine structured MMNCs have a higher room temperature strength and better high temperature performance due to grain boundary strengthening, nanoparticle strengthening and Zener pinning effects compared to their metal matrices. On the scientific aspect, there is the question of whether the linear superposition of basic strengthening mechanisms, which is applicable to conventional precipitation-hardened alloys, is still valid in evaluating the strength of ultrafine structured MMNCs. In general, there might be a synergistic effect among different strengthening mechanisms when the grain sizes of matrices of MMNCs are reduced down to the submicrometer range. In this thesis, a model system of Cu-5vol.%Al₂O₃ was selected to study with the aim of deepening and reinforcing the understanding of the microstructure/property relationship and contributions of various strengthening mechanisms to the overall strength of ultrafine structured MMNCs. Nanostructured Cu-5vol.%Al₂O₃ nanocomposite powder particles were produced by high energy mechanical milling (HEMM) of a powder mixture of Cu powder and Al₂O₃ nanopowder. The nanocomposite powders were then annealed at 300-600°C for up to 5 h. The powders had a high thermal stability at temperatures up to 600°C. After annealing at 600°C for 5 h, Cu nanograins in the microstructure of the nanocomposite powder particles only grew slightly and the microstructure of the Cu matrix of powder particles was still well within the nanostructure range. The activation energy for the grain growth of the Cu nanograins was determined to be 63.4 kJ/mol, which is much lower than that of coarse grained monolithic Cu and similar to that of nanocrystalline monolithic Cu, and suggests the grain growth behavior is controlled by grain boundary diffusion. The impressive thermal stability of the microstructure of the powder particles is mainly associated with the effect of Al₂O₃ nanoparticles on the grain growth through inhibiting the grain boundary diffusion. Ultrafine structured Cu-5vol.%Al₂O₃ nanocomposite samples were synthesized by powder compact extrusion at 750 and 900°C, and their microstructures and tensile properties were characterized. The microstructural characterization showed that there is no significant difference in the mean Cu grain sizes for both samples but the sample extruded at 900°C has far less Al₂O₃ nanoparticles in comparison to the sample extruded at 750°C. The tensile testing results exhibited that the 900°C extruded sample has a larger strength and higher ductility at fracture as compared to those of the 750°C extruded sample. This shows that the dissolution of Al₂O₃ nanoparticles in the Cu matrix takes place when the powder compact is heated and extruded at 900°C, and the dissolution of the Al₂O₃ nanoparticles leads to superior tensile properties of the sample extruded at 900°C. Further ultrafine structured Cu-5vol.%Al₂O₃ nanocomposite samples were prepared by extrusion of powder compacts of nanostructured Cu-5vol.%Al₂O₃ nanocomposite powder at temperatures ranging from 300 to 900°C. The experimental results showed that Cu grains and the sizes and volume fractions of Al₂O₃ nanoparticles of bulk ultrafine structured Cu-5vol.%Al₂O₃ nanocomposite samples increased with the increase of the extrusion temperature. The average sizes of Cu grains and Al₂O₃ nanoparticles and the volume fraction of Al₂O₃ nanoparticles of the extruded samples increased from 132 nm, 43 nm and 0.75% to 263 nm, 100 nm and 4%, respectively, as the extrusion temperature increased from 300 to 900°C. The increases in the sizes and volume fraction of the Al₂O₃ nanoparticles with the increase of the extrusion temperature were caused by the precipitation of Al₂O₃ nanoparticles during extrusion. The samples extruded at 400°C or lower fractured prematurely without yielding, while the samples extruded at T≥500°C fractured after yielding. The yield strengths and ultimate tensile strengths of such materials changed only slightly with the increase of the extrusion temperature and had values in the range 466-517 and 546-564 MPa. However, the tensile ductility of the extruded samples was proportional to the extrusion temperature and increased from 0.76 to 5.82% with increasing the extrusion temperature from 500 to 900°C. The slight decrease of yield strength and significant increase of the ductility of the consolidated sample with increasing extrusion temperature suggests that the level of interparticle atomic bonding in the consolidated samples increases with increased extrusion temperature. It is speculated that the fracture of the samples extruded at T ≤800°C is associated with the weak bonding of residual interparticle boundaries which have not been transformed into grain boundaries. When the extrusion temperature T ≥800°C, the area of the residual interparticle boundaries may be too small to play any major role in causing the fracture of the consolidated sample. Analysis of the contributions of different strengthening mechanisms demonstrates that grain boundary strengthening makes the largest contribution to the strength of the extruded samples relative to the nanoparticle strengthening and strain hardening and experimentally measured yield strength of the extruded samples can be predicted appropriately by the sum of Peierls stress, grain boundary strengthening, nanoparticle strengthening and strain hardening. The effect of annealing on an ultrafine structured Cu-5vol.%Al₂O₃ nanocomposite sample made by powder compact extrusion at 900°C was investigated by annealing for 1h at different temperatures in the range of 500-900°C. This revealed that Al₂O₃ nanoparticles provided excellent thermal stability to the ultrafine structured Cu-5vol.%Al₂O₃ nanocomposite sample. The microstructure and microhardness of the sample remained stable up to annealing at 800°C for 1 h. High resistance of Al₂O₃ nanoparticles to coarsening was responsible for this high thermal stability. The microhardness increase observed for the sample annealed at 700°C for 1 h came from the precipitation of small Al₂O₃ nanoparticles. On the other hand, the sudden drop in microhardness of the sample annealed at 900°C for 1 h was related to the coarsening of small Al₂O₃ nanoparticles and grain growth of the Cu matrix. This thesis concludes with suggestions for future work that would extend on from the findings presented here.
Type
Thesis
Type of thesis
Series
Citation
Zhou, D. (2014). Thermal Stability, Microstructures and Mechanical Properties of Nanostructured/Ultrafine Structured Cu-5vol.%Al₂O₃ Nanocomposites Fabricated by High Energy Mechanical Milling and Powder Compact Extrusion (Thesis, Doctor of Philosophy (PhD)). University of Waikato, Hamilton, New Zealand. Retrieved from https://hdl.handle.net/10289/8835
Date
2014
Publisher
University of Waikato
Rights
All items in Research Commons are provided for private study and research purposes and are protected by copyright with all rights reserved unless otherwise indicated.