Loading...
Thumbnail Image
Publication

The Effect of Moisture Content and Extrusion Temperature on the Processing, Thermal and Mechanical Properties of Novatein®

Abstract
The recent effect of petroleum based synthetic plastic on economy and environment has led to ever increasing study of renewable natural polymers such as proteins. Novatein Thermoplastic (NTP) is a protein based thermoplastic processed from bloodmeal. Bloodmeal is a by-product of the animal slaughter house and it is widely sold and used as low cost fertilizer and animal feed. It contains 90% dry weight of protein and it can biodegrade under suitable conditions making it a better alternative to petroleum based synthetic plastics. The objective of this thesis was to investigate the effect of processing water and extrusion temperature on the processing, thermal and mechanical properties of urea free NTP to optimize processing temperature and formulation for this material. Literature revealed that extrusion processing of protein applies considerable amount of heat and shear into protein material to form polymer melt requiring sufficient chain mobility which could be achieved through the lowering of the glass transition temperature (Tg) of protein with the addition of water and other additives. Also literature revealed that optimization of material properties of protein thermoplastic is highly dependent on extrusion processing parameters such as extrusion temperature, initial moisture content (processing water), torque, pressure, screw-speed and specific mechanical energy (SME). Four formulations of Novatein were processed using bloodmeal powder with Sodium Sulfite (SS), Sodium Dodecyl Sulfate (SDS), Tri ethylene glycol (TEG) and varying Water content at 30, 35, 40 and 45pphBM. The resultant thermoplastic was extruded using varying die temperatures of 120 °C, 130 °C, 140 °C and 150 °C. Test pieces were produced using injection moulding and conditioned for 7days The effect of processing water and extrusion temperature was characterized by • Extrusion Processing, processing water between 30 to 35pphBM produced consolidated material because of protein chain unravelling and above this water content, material produced was mostly not consolidated due to irregularities in measured torque and pressure as a result of inconsistent feed-rate which is caused by excessive plasticization of the material. • Moisture Content, after conditioning assumed water content measured at oven drying ranged between 4% to 15% with 9 out of the 16 experiments falling within the accepted narrower range of 8% to 11%. The remaining 7, all experiment in formulation 4 had higher moisture content than the acceptable range and all experiment extruded at die temperature of 150 °C had lower moisture content than the acceptable range. • Mechanical properties, water was shown to be critical for processing as it acted as plasticizer lowering the glass transition temperature (Tg) and denaturing temperature of the protein material. During conditioning moisture was lost resulting to a brittle material because of the new interaction between the protein chains after conditioning. There was no clear trend when considering the effect of extrusion die temperatures used on the mechanical properties of Novatein. • DMA, increasing processing water decreased Tg while increasing temperature, the 9 experiment with the acceptable range, at 30pphBM showed increase in Tg and at 35 and 40pphBM no increase was observed, the 7 experiments outside the acceptable narrower range showed no significant difference in Tg within their range. There was an insignificant difference in Tg when considering the effect of added water and processing temperature therefore the difference is as a result of water remaining in the sample when they were tested. • TGA, showed varying residual moisture content as after freeze drying and milling the mass loss observed varied between 3% to 17% for all experiments which could be as a result of samples not freeze dried to the same extent or protein absorbing water from the atmosphere during milling because of its hygroscopic nature. There is an insignificant difference in moisture content after conditioning and subsequent freeze drying. There is no effect on the decomposition behaviour and thermal stability of Novatein within the range of processing water and extrusion temperature used as there was an insignificant difference observed in the TGA thermograms after freeze drying and milling. • WAXS, crystallinity of the tested formulation ranged from 15% to 27% where most were within the range of 19% and 22% which fell within the reported crystallinity range of Novatein from previous study demonstrating that the range obtained was the appropriate range for NTP therefore no change in crystallinity was observed. The optimal processing temperature and formulation was achieved using 35pphBM water and extrusion die temperature of 150 °C (experiment 8). It showed ease of processing, having good mechanical properties. Before conditioning it had tensile strength of 5.35MPa, Young’s modulus of 253MPa, strain at break of 0.34mm/mm, toughness of 1.61Mpa and after conditioning it had tensile strength of 17.49MPa, Young’s modulus of 1101MPa, strain at break of 0.02mm/mm and toughness of 0.18MPa. Thermal property showed no significant difference therefore there is no change in thermal property of Novatein with this optimal processing temperature and formulation.
Type
Thesis
Type of thesis
Series
Citation
Izuchukwu, S. C. P. (2015). The Effect of Moisture Content and Extrusion Temperature on the Processing, Thermal and Mechanical Properties of Novatein® (Thesis, Master of Engineering (ME)). University of Waikato, Hamilton, New Zealand. Retrieved from https://hdl.handle.net/10289/9506
Date
2015
Publisher
University of Waikato
Rights
All items in Research Commons are provided for private study and research purposes and are protected by copyright with all rights reserved unless otherwise indicated.