Loading...
3D printing of bio-inspired, multi-material structures to enhance stiffness and toughness
Abstract
In nature, many biological, multi-materials have complex microstructures and excellent mechanical properties. One shellfish material called nacre has received much attention due to its unique interlocking structure of alternating calcium carbonate tablet and soft organic matter filler. It has microstructure features such as waviness which provide high strength and toughness properties. As a popular topic in the study of bio-inspired structure, it is of great significance to study the ordered microstructure and toughening mechanism of nacre.
3D printing allows for the easy manufacture of complex structures. In this project, inspired by the high strength and toughness of natural nacre, 3D printing technology was used to prepare nacre-like, multi-material structure. Tensile tests, cyclic tensile test and fracture toughness tests were carried out to investigate the relationship between multi-material structure geometry and tensile properties, fracture modes and toughness behaviour.
In the experimental part of this thesis, specimens of the tablet-filler with different dovetail angles made by polylactic acid (PLA) and thermoplastic polyurethane (TPU) inspired by the microstructure of nacre structure were prepared through Fused filament fabrication (FFF)/ Fused Deposition Modelling (FDM) type of 3D printing technology. The multi-material dovetail PLA & TPU specimens exhibited multi-stage deformation under tensile testing. By comparing the tensile performance of structure made by dovetail PLA & PLA material as well as unidirectional pure PLA specimen, it was confirmed that the incorporation of soft TPU filler gave the opportunity for tablet sliding, resulting in a complex multi-stage deformation mechanism of the structures.
Two modes of failure mechanisms, tablet pull-out and tablet break, were observed for the multi-material PLA & TPU structure under tensile testing. The combination of tablet break and pull-out modes can lead to higher strength and modulus than tablet pull-out. In the tablet pull-out mode, transverse expansion was observed in the larger angle dovetail structure, and the occurrence of negative Poisson's ratio effect was determined by calculation. In addition, there is a distinct plateau stage in the tensile curve of multi-material PLA & TPU structure, through cyclic tensile tests identified the plateau as a yield point, generated by short interface between tablets and filler broken. The cyclic tensile tests also determined that the main deformation resistance of the PLA & TPU structure was provied by the long interface broken between tablets and filler, also the interlocking and shearing between the dovetail angle tablets.
Multi-material PLA & TPU structures with larger dovetail angles produced greater plastic deformation and absorbed more energy during tensile testing. Multi-material PLA & TPU with 5˚ dovetail showed the highest ultimate tensile strength 11.46 MPa and Young’s modulus of 495.96 MPa, but 9˚ dovetail performed poorly with 6.51 MPa and 395.48 MPa, respectively. The value even below than 1˚ dovetail (ultimate tensile strength of 9.82 MPa, modulus of 453.38 MPa). The ultimate tensile strength and Young’s modulus of the multi-material PLA & TPU structure are not as high as those of unidirectional pure PLA and dovetail PLA & PLA specimen, but energy absorption performance is improved by soft TPU filler and dovetail angles. In fracture experiments, crack extension behaviour was observed in fracture toughness specimens.
In summary, the mechanical properties of the nacre-like, multi-material structure were investigated by tensile behavior, fracture mode and energy absorption analysis in this paper. It is demonstrated that the combination of stiff tablet material and soft filler material can effectively improve the toughness of the structure. The tensile strength of the multi-material structure can be improved by increasing the dovetail angle of the tablet. However, it has not been observed that increasing the dovetail angle can significantly increase stiffness. It is confirmed that the optimized design of the 3D printed, bio-inspired, multi-material structure can change the mechanical behavior of the structure and improve its mechanical properties, can provide new ideas for the development of composite materials with excellent mechanical properties.
 
Type
Thesis
Type of thesis
Series
Citation
Date
2021
Publisher
The University of Waikato
Supervisors
Rights
All items in Research Commons are provided for private study and research purposes and are protected by copyright with all rights reserved unless otherwise indicated.